View ADCMP572_973855.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

Preliminary Technical Data
FEATURES
3.3 V/5.2 V single-supply operation 150 ps propagation delay 15 ps overdrive and slew rate dispersion 8 GHz equivalent input risetime bandwidth 80 ps minimum pulse width 35 ps typical output rise/fall 10 ps deterministic jitter (DJ) 200 fs random jitter (RJ) On-chip terminations at both input pins Robust inputs with no output phase reversal Resistor programmable hysteresis Differential latch control Power supply rejection > 70 dB
Ultrafast 3.3 V Single-Supply Comparators ADCMP572/ADCMP573
FUNCTIONAL BLOCK DIAGRAM
VCCI VCCO
VTP TERMINATION VP NONINVERTING INPUT VN INVERTING INPUT VTN TERMINATION LE INPUT HYS LE INPUT
04409-0-025
ADCMP572 ADCMP573
Q OUTPUT CML/ RSPECL Q OUTPUT
Figure 1.
APPLICATIONS
Automatic test equipment (ATE) High speed instrumentation Pulse spectroscopy Medical imaging and diagnostics High speed line receivers Threshold detection Peak and zero-crossing detectors High speed trigger circuitry Clock and data signal restoration
GENERAL DESCRIPTION
The ADCMP572/ADCMP573 are ultrafast comparators fabricated on Analog Devices, Inc.'s proprietary XFCB3 Silicon Germanium (SiGe) bipolar process. The ADCMP572 features CML output drivers, and the ADCMP573 features reduced swing PECL (RSPECL) output drivers. Both devices offer 150 ps propagation delay and 100 ps minimum pulse width for 10 Gbps operation with 200 fs RMS random jitter (RJ). Overdrive and slew rate dispersion is typically less than 15 ps. A flexible power supply scheme allows either device to operate with a single +3.3 V positive supply and a -0.2 V to +1.2 V input signal range, or with split input/output supplies to support a wider -0.2 V to +3.2 V input signal range and an independent range of output levels. 50 on-chip termination resistors are provided at both inputs with the optional capability to leave open (on an individual pin basis) for applications requiring high impedance inputs. The CML output stage is designed to directly drive 400 mV into 50 transmission lines terminated to between 3.3 V to 5.2 V. The RSPECL output stage is designed to drive 400 mV into 50 terminated to VCCO - 2 V and is compatible with several commonly used PECL logic families. The comparator input stage offers robust protection against large input overdrive, and the outputs do not phase reverse when the valid input signal range is exceeded. High speed latch and programmable hysteresis features are also provided. The ADCMP572/ADCMP573 are available in a 16-lead LFCSP package.
Rev. PrB
Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties that may result from its use. Specifications subject to change without notice. No license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Trademarks and registered trademarks are the property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A. Tel: 781.329.4700 www.analog.com Fax: 781.326.8703 (c) 2004 Analog Devices, Inc. All rights reserved.
ADCMP572/ADCMP573 TABLE OF CONTENTS
Electrical Characteristics ................................................................. 3 Absolute Maximum Ratings............................................................ 5 ESD Caution.................................................................................. 5 Pin Configuration and Function Descriptions............................. 6 Typical Performance Characteristics ............................................. 7 Application Information.................................................................. 9 Power/Ground Layout and Bypassing ....................................... 9 CML/RSPECL Output Stage ....................................................... 9 Using/Disabling the Latch Feature............................................. 9
Preliminary Technical Data
Optimizing High Speed Performance ..................................... 10 Comparator Propagation Delay Dispersion ........................... 10 Comparator Hysteresis .............................................................. 11 Minimum Input Slew Rate Requirement ................................ 11 Typical Application Circuits.......................................................... 12 Timing Information ....................................................................... 13 Outline Dimensions ....................................................................... 14 Ordering Guide .......................................................................... 14
REVISION HISTORY
6/04--Revision PrB: Preliminary Version 2/04--Revision PrA: Preliminary Version
Rev. PrB | Page 2 of 16
Preliminary Technical Data ELECTRICAL CHARACTERISTICS
VCCI = VCCO = 3.3 V, TA = 25C, unless otherwise noted. Table 1.
Parameter DC INPUT CHARACTERISTICS Input Voltage Range Input Differential Voltage Input Offset Voltage Offset Voltage Tempco Input Bias Current Input Bias Current Tempco Input Offset Current Input Capacitance Input Impedance Input Resistance, Differential Mode Input Resistance, Common Mode Active Gain Common-Mode Rejection Symbol VP, VN Conditions VCCI = 3.3 V, VCCO = 3.3 V VCCI = 5.2 V, VCCO = 3.3 V Min -0.2 -0.2 -1.2 -5.0 -50.0 -5.0 CP, CN 47.5 Open termination Open termination AV CMRR VCCI = 3.3 V, VCCO = 3.3 V, VCM = 0.0 V to 1.0 V VCCI = 5.2 V, VCCO = 3.3 V, VCM = 0.0 V to 3.0 V
ADCMP572/ADCMP573
Typ
Max +1.2 +3.2 +1.2 +5.0 0.0 +5.0 52.5
Unit V V V mV V/C A nA/C A pF k k dB dB dB mV
VOS VOS/dT IP, IN
Open termination
2.0 10.0 -25.0 50.0 2.0 TBD 50 50 500 54 50 40 1
Hysteresis LATCH ENABLE CHARACTERISTICS ADCMP572 Latch Enable Input Range Latch Enable Input Differential Latch Setup Time Latch Hold Time ADCMP573 Latch Enable Input Range Latch Enable Input Differential Latch Setup Time Latch Hold Time Latch Enable Input Impedance Latch to Output Delay Latch Minimum Pulse Width DC OUTPUT CHARACTERISTICS ADCMP572 (CML) Output Impedance Output Voltage High Level Output Voltage Low Level Output Voltage Differential Temperature Coefficient, VOH Temperature Coefficient, VOL ADCMP573 (RSPECL) Output Voltage High Level Output Voltage Low Level Output Voltage Differential
RHYS =
2.8 0.2 tS tH VOD = 100 mV VOD = 100 mV 1.8 0.2 tS tH tPLOH, tPLOL tPL VOD = 100 mV VOD = 100 mV 47.5 VOD = 100 mV VOD = 100 mV
0.4 15 0
VCCO+0.2 0.5
V V ps ps V V ps ps ps ps
0.4 0 50 50.0 150 100
VCCO-0.6 0.5
52.5
ZOUT VOH VOL VOH/dT VOL/dT VOH VOL
-8 mA < I OUT < 8 mA 50 terminate to VCCO 50 terminate to VCCO 50 terminate to VCCO 50 terminate to VCCO 50 terminate to VCCO 50 terminate to VCCO-2.0 50 terminate to VCCO-2.0 50 terminate to VCCO-2.0
47.5 VCCO-0.10 VOH-0.45 350
50.0 VCCO-0.05 VOH-0.40 400 TBD TBD VCCO-0.80 VOH-0.40 400
52.5 VCCO VOH-0.35 450
V V mV mV/C mV/C V V mV
VCCO-0.90 VOH-0.45 350
VCCO-0.70 VOH-0.35 450
Rev. PrB | Page 3 of 16
ADCMP572/ADCMP573
Parameter AC PERFORMANCE Propagation Delay Symbol tPD Conditions VCCI = 3.3 V, VOD = 200 mV VCCI = 3.3 V, VOD = 20 mV VCCI = 5.2 V, VOD = 200 mV VOD = 200 mV, 5 V/ns 50 mV < VOD < 1.0 V, 5 V/ns 10 mV < VOD < 1.0 V, 5 V/ns 2 V/ns to 10 V/ns 100 ps to 5 ns VCCI = 3.3 V, 1 V/ns, VCM = 0 V VCCI = 5.2 V, 1 V/ns, VCM = 0 V VOD=0.4V, 0.0 V < VCM < 1.0 V 0.0 V to 400 mV input tR = tF = 25 ps, 20/80 > 50% Output Swing VOD = 200 mV, 5 V/ns, PRBS31-1 NRZ, 4 Gbps VOD = 200 mV, 5 V/ns, PRBS31-1 NRZ, 10 Gbps
VOD = 200 mV, 5 V/ns, 1.25 GHz
Preliminary Technical Data
Min Typ 150 165 145 0.5 10 10 15 15 5 5 10 5 8.0 12.5 10 TBD 0.2 100 80 35 35 3.1 3.1 -0.2 5.4 5.4 +2.3 Max Unit ps ps ps ps/C ps ps ps ps ps ps ps/V GHz Gbps ps ps ps ps ps ps ps V V V
Propagation Delay Tempco Prop Delay Skew--Rising Transition to Falling Transition Overdrive Dispersion Slew Rate Dispersion Pulse Width Dispersion Duty Cycle Dispersion Common-Mode Dispersion Equivalent Input Bandwidth1 Toggle Rate Deterministic Jitter Deterministic Jitter RMS Random Jitter Minimum Pulse Width Minimum Pulse Width Rise Time Fall Time POWER SUPPLY Input Supply Voltage Range Output Supply Voltage Range Positive Supply Differential ADCMP572 (CML) Positive Supply Current
tPD/dT
BWEQ
DJ DJ RJ PWMIN PWMIN tR tF VCCI VCCO VCCI -VCCO IVCCI + IVCCO
tPD/PW < 5 ps tPD/PW < 10 ps 20/80 20/80
Power Dissipation
PD
VCCI = 3.3 V, VCCO = 3.3 V, terminate 50 to VCCO VCCI = 5.2 V, VCCO = 5.2 V, terminate 50 to VCCO VCCI = 3.3 V, VCCO = 3.3 V, terminate 50 to VCCO VCCI = 5.2 V, VCCO = 5.2 V, terminate 50 to VCCO VCCI = 3.3 V, VCCO = 3.3 V, 50 to VCCO - 2 V VCCI = 5.2 V, VCCO = 5.2 V, 50 to VCCO - 2V VCCI = 3.3 V, VCCO = 3.3 V, 50 to VCCO - 2 V VCCI = 5.2 V, VCCO = 5.2 V, 50 to VCCO - 2 V VCCI = 3.3 V 5%, VCCO = 3.3 V
44 44 145 240
52 52 160 265
mA
mW
ADCMP573 (RSPECL) Positive Supply Current
IVCCI + IVCCO
66 68 145 175 74
74 76 160 195
mA
Power Dissipation
PD
mW
Power Supply Rejection--VCCI
PSRVCCI
dB
1
Equivalent Input Bandwidth assumes a simple first-order response and is calculated with the following formula: BWEQ = 0.22/*(trCOMP2-trIN2), where trIN is the 20/80 transition time of a quasi-Gaussian signal applied to the comparator input and trCOMP is the effective transition time digitized by the comparator. Rev. PrB | Page 4 of 16
Preliminary Technical Data ABSOLUTE MAXIMUM RATINGS
Table 2.
Parameter SUPPLY VOLTAGES Input Supply Voltage (VCCI to GND) Output Supply Voltage (VCCO to GND) Positive Supply Differential (VCCI - VCCO) INPUT VOLTAGES Input Voltage Differential Input Voltage Input Voltage, Latch Enable HYSTERESIS CONTROL PIN Applied Voltage (HYS to GND) Maximum Input/Output Current OUTPUT CURRENT ADCMP572 (CML) ADCMP573 (RSPECL) TEMPERATURE Operating Temperature, Ambient Operating Temperature, Junction Storage Temperature Range Rating -0.5 V to +6.0 V -0.5 V to +6.0 V -0.5 V to +3.5 V
ADCMP572/ADCMP573
Thermal Considerations The ADCMP572/ADCMP573 LFCSP 16-lead package has a JA (junction to ambient thermal resistance) of 70C/W in still air. Stress above those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability.
-0.5 V to VCCI + 0.5 V (VCCI + 0.5 V) -0.5 V to VCCO + 0.5 V -0.5 V to +1.5 V 1 mA 20 mA -35 mA -40C to +85C 125C -65C to +150C
ESD CAUTION
ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily accumulate on the human body and test equipment and can discharge without detection. Although this product features proprietary ESD protection circuitry, permanent damage may occur on devices subjected to high energy electrostatic discharges. Therefore, proper ESD precautions are recommended to avoid performance degradation or loss of functionality.
Rev. PrB | Page 5 of 16
ADCMP572/ADCMP573 PIN CONFIGURATION AND FUNCTION DESCRIPTIONS
GND
16 15 PIN1 14 13 12 11 10 9 5 6 7 8
Preliminary Technical Data
GND VCCI HYS
VTP 1 VP 2 VN 3 VTN 4
VCCI
VCCO Q Q VCCO
04409-0-026
ADCMP572 ADCMP573
TOP VIEW (Not to Scale)
Figure 2. ADCMP572/ADCMP573 Pin Configuration
Table 3. Pin Function Descriptions
Pin No. 1 2 3 4 5, 16 6 Mnemonic VTP VP VN VTN VCCI LE Description Termination Resistor Return Pin for VP Input. Noninverting Analog Input. Inverting Analog Input. Termination Resistor Return Pin for VN Input. Positive Supply Voltage for Input Stage. Latch Enable Input Pin, Inverting Side. In compare mode (LE = low), the output tracks changes at the input of the comparator. In latch mode (LE = high), the output reflects the input state just prior to the comparator's being placed in latch mode. LE must be driven in compliment with LE. Latch Enable Input Pin, Noninverting Side. In compare mode (LE = high), the output tracks changes at the input of the comparator. In latch mode (LE = low), the output reflects the input state just prior to the comparator's being placed in latch mode. LE must be driven in compliment with LE. Termination Return Pin for the LE/LE Input Pins. For the ADCMP572 (CML output stage), this pin should be connected to the positive VCCO supply. For the ADCMP573 (RSPECL output stage), this pin should be connected to the VCCO - 2 V termination potential. Ground. Positive Supply Voltage for the CML/RSPECL Output Stage. Inverting Output. Q is at logic low if the analog voltage at the noninverting input, VP, is greater than the analog voltage at the inverting input, VN, provided the comparator is in compare mode. See the LE/LE description (Pins 6 and 7) for more information. Noninverting Output. Q is at logic high if the analog voltage at the noninverting input VP is greater than the analog voltage at the inverting input, VN, provided the comparator is in compare mode. See the LE/LE description (Pins 6 and 7) for more information. Hysteresis Control Pin. Leave this pin disconnected for zero hysteresis. Connect to GND with a suitably sized resistor to add the desired amount of hysteresis. Refer to Figure 7 for proper sizing of RHYS hysteresis control resistor. The metallic back surface of the package is not electrically connected to any part of the circuit, and it can be left floating for best electrical isolation between the package handle and the substrate of the die. But it can also be soldered to the application board if improved thermal and/or mechanical stability is desired.
7
LE
8
VCCO/VTT
13, 15 9, 12 10
GND VCCO Q
11
Q
14
HYS
Heatsink
N/C
Rev. PrB | Page 6 of 16
VCCO/VTT
LE
LE
Preliminary Technical Data TYPICAL PERFORMANCE CHARACTERISTICS
VCCI = VCCO = 3.3 V, TA = 25C, unless otherwise noted.
20
ADCMP572/ADCMP573
39.0
PROPAGATION DELAY ERROR (ps)
38.5
15
RISE/FALL TIME (ps)
38.0
10
37.5
37.0
5
36.5
0
50
100
150
200
250
-40
-20
0
20
40
60
80
100
INPUT OVERDRIVE VOLTAGE (mV)
TEMPERATURE (C)
Figure 3. Propagation Delay vs. Input Overdrive
Figure 6. Rise/Fall Time vs. Temperature
158.5
60
158.0
PROPAGATION DELAY (ps)
50
HYSTERESIS (mV)
157.5
40
157.0
30
156.5
20
156.0
10
04409-0-040
0
0.2
0.4
0.6
0.8
1.0
1.2
0
1
2
3 RHYS (k)
4
5
6
INPUT COMMON-MODE VOLTAGE (V)
Figure 4. Propagation Delay vs. Input Common Mode
160
Figure 7. Hysteresis vs. RHYS Control Resistor
-15.0
158
PROPAGATION DELAY (ps) INPUT BIAS CURRENT (A)
-15.5
156 154
-16.0 -16.5
152
-17.0
150
-17.5
148 146 -60
-18.0
04409-0-041
-40
-20
0
20
40
60
80
100
-0.3
-0.1
0.1
0.3
0.5
0.7
0.9
1.1
1.3
1.5
TEMPERATURE (C)
VP INPUT VOLTAGE (VN = -0.2V)
Figure 5. Propagation Delay vs. Temperature
Figure 8. Input Bias Current vs. Input Differential
Rev. PrB | Page 7 of 16
04409-0-044
-18.5 -0.5
04409-0-043
155.5
0
04409-0-042
04409-0-039
0
36.0 -60
ADCMP572/ADCMP573
-16.2 380 -16.3
INPUT BIAS CURRENT (A)
Preliminary Technical Data
379
-16.5
OUTPUT LEVELS (mV)
04409-0-045
-16.4
378 377
-16.6
376
-16.7
375
-16.8 -16.9 -60
374 373 -60
-40
-20
0
20
40
60
80
100
-40
-20
0
20
40
60
80
100
TEMPERATURE (C)
TEMPERATURE (C)
Figure 9. Input Bias Current vs. Temperature
Figure 11. Output Levels vs. Temperature
Figure 10. Input Offset Voltage vs. Temperature
Rev. PrB | Page 8 of 16
04409-0-046
Preliminary Technical Data APPLICATION INFORMATION
POWER/GROUND LAYOUT AND BYPASSING
The ADCMP572/ADCMP573 comparators are very high speed SiGe devices. Consequently, it is essential to use proper high speed design techniques to achieve the specified performance. Of critical importance is the use of low impedance supply planes, particularly the output supply plane (VCCO) and the ground plane (GND). Individual supply planes are recommended as part of a multilayer board. Providing the lowest inductance return path for switching currents ensures the best possible performance in the target application. It is also important to adequately bypass the input and output supplies. A 1 F electrolytic bypass capacitor should be placed within several inches of each power supply pin to ground. In addition, multiple high quality 0.1 F bypass capacitors should be placed as close as possible to each of the VCCI and VCCO supply pins and should be connected to the GND plane with redundant vias. High frequency bypass capacitors should be carefully selected for minimum inductance and ESR. Parasitic layout inductance should also be strictly avoided to maximize the effectiveness of the bypass at high frequencies. If the input and output supplies are connected separately such that VCCI VCCO, then care should be taken to bypass each of these supplies separately to the GND plane. A bypass capacitor should not be connected between them. It is recommended that the GND plane separate the VCCI and VCCO planes when the circuit board layout is designed to minimize coupling between the two supplies and to take advantage of the additional bypass capacitance from each respective supply to the ground plane. This enhances the performance when split input/output supplies are used. If the input and output supplies are connected together for single-supply operation such that VCCI = VCCO, then coupling between the two supplies is unavoidable; however, every effort should be made to keep the supply plane adjacent to the GND plane to maximize the additional bypass capacitance this arrangement provides.
ADCMP572/ADCMP573
stripline techniques are essential to ensure proper transition times and to prevent output ringing and pulse-width dependant propagation delay dispersion. For the most timing critical applications where transmission line reflections pose the greatest risk to performance, the ADCMP572 provides the best match to 50 output transmission paths.
VCCO
50
Q Q
16mA
04409-0-037
GND
Figure 12. Simplified Schematic Diagram of the ADCMP572 CML Output Stage
VCCO
Q Q
GND
Figure 13. Simplified Schematic Diagram of the ADCMP573 RSPECL Output Stage
CML/RSPECL OUTPUT STAGE
Specified propagation delay dispersion performance can be achieved only by using proper transmission line terminations. The outputs of the ADCMP572 are designed to directly drive 400 mV into 50 cable or microstrip and/or stripline transmission lines properly terminated to the VCCO supply plane. The CML output stage is shown in the simplified schematic diagram of Figure 12. The outputs are each back-terminated with 50 for best transmission line matching. The RSPECL outputs of the ADCMP573 are illustrated in Figure 13 and should be terminated to VCCO - 2 V. As an alternative, Thevenin equivalent termination networks may also be used in either case if the direct termination voltage is not readily available. If high speed output signals must be routed more than a centimeter, microstrip or
USING/DISABLING THE LATCH FEATURE
The latch inputs (LE/LE) are active low for latch mode, and are internally terminated with 50 resistors to Pin 8. This corresponds to the VCCO supply for the ADCMP572 and the VTT pin for the ADCMP573. All VCCO pins should be connected to the supply plane for maximum performance, and the VTT pin should be connected externally to VCCO - 2 V, preferably to its own low inductance plane. When using the ADCMP572, the latch function can be disabled by connecting the LE pin to GND with an external pull-down resistor and leaving the LE pin unconnected. To prevent excessive power dissipation, the resistor should be 750 when VCCO = 3.3 V, and 1.2 k when VCCO = 5.2 V. When using the ADCMP573 comparator, the latch can be disabled by connecting the LE pin to VCCO with an
Rev. PrB | Page 9 of 16
04409-0-038
ADCMP572/ADCMP573
external 500 resistor, and leaving the LE pin disconnected. In this case, the resistor value does not depend on the chosen VCCO supply voltage, assuming the VTT pin is properly connected to VCCO - 2 V.
Preliminary Technical Data
COMPARATOR PROPAGATION DELAY DISPERSION
The ADCMP572/ADCMP573 comparators are designed to reduce propagation delay dispersion over a wide input overdrive range of 5 mV to 500 mV. Propagation delay dispersion is a variation in propagation delay that results from a change in the degree of overdrive or slew rate (how far or how fast the input signal exceeds the switching threshold). Propagation delay dispersion is a specification that becomes important in high speed time critical applications such as data communication, automatic test and measurement, instrumentation, and event-driven applications such as pulse spectroscopy, nuclear instrumentation, and medical imaging. Dispersion is defined as the variation in propagation delay as the input overdrive conditions are changed (Figure 14 and Figure 15). For the ADCMP572/ADCMP573, dispersion is typically <15 ps because the overdrive is varied from 10 mV to 500 mV, and the input slew rate is varied from 2 V/ns to 10 V/ns. This specification applies for both positive and negative signals since the ADCMP572/ADCMP573 has substantially equal delays for either positive-going or negative-going inputs.
500mV OVERDRIVE
OPTIMIZING HIGH SPEED PERFORMANCE
As with any high speed comparator, proper design and layout techniques are essential to obtaining the specified performance. Stray capacitance, inductance, inductive power and ground impedances, or other layout issues can severely limit performance and can often cause oscillation. Discontinuities along input and output transmission lines can also severely limit the specified pulse-width dispersion performance. For applications working in a 50 environment, input and output matching has a significant impact on data dependant (or deterministic) jitter (DJ) and pulse-width dispersion performance. The ADCMP572/ADCMP573 comparators provide internal 50 termination resistors for both VP and VN inputs, and the ADCMP572 provides 50 back terminated outputs. The return side for each input termination is pinned out separately with the VTP and VTN pins, respectively. If a 50 termination is desired at one or both of the VP/VN inputs, then the VTP and VTN pins can be connected (or disconnected) to (from) the desired termination potential as required. The termination potential should be carefully bypassed using high quality bypass capacitors as discussed above to prevent undesired aberrations on the input signal due to parasitic inductance in the circuit board layout. If a 50 input termination is not desired, either one or both of the VTP/VTN termination pins can be left disconnected. In this case, the pins should be left floating with no external pull-downs or bypassing capacitors. It should be understood that when leaving an input termination disconnected, the internal resistor acts as a small stub on the input transmission path and can cause problems for very high speed inputs. Reflections should then be expected from the comparator inputs because they no longer provide a matched impedance to the input path leading to the device. It then becomes important to back-match the drive source impedance to the input transmission path to minimize multiple reflections. For applications in which the comparator is very close to the driving signal source, the source impedance should be minimized. High source impedance in combination with parasitic input capacitance of the comparator could cause an undesirable degradation in bandwidth at the input, thus degrading the overall response. Although the ADCMP572/ ADCMP573 comparators have been designed to minimize input capacitance, some parasitic capacitance is inevitable. It is therefore recommended that the drive source impedance be no more than 50 for best high speed performance.
INPUT VOLTAGE 10mV OVERDRIVE VN VOS
DISPERSION Q/Q OUTPUT
Figure 14. Propagation Delay--Overdrive Dispersion
INPUT VOLTAGE 1V/ns VN VOS 10V/ns
DISPERSION Q/Q OUTPUT
Figure 15. Propagation Delay--Slew Rate Dispersion
Rev. PrB | Page 10 of 16
04409-0-028
04409-0-027
Preliminary Technical Data
COMPARATOR HYSTERESIS
The addition of hysteresis to a comparator is often desirable in a noisy environment or when the differential input amplitudes are relatively small or slow moving. The transfer function for a comparator with hysteresis is shown in Figure 16. If the input voltage approaches the threshold (0.0 V in this example) from the negative direction, the comparator switches from a low to a high when the input crosses +VH/2. The new switching threshold becomes -VH/2. The comparator remains in the high state until the threshold -VH/2 is crossed from the positive direction. In this manner, noise centered on 0.0 V input does not cause the comparator to switch states unless it exceeds the region bounded by VH/2.
OUTPUT
ADCMP572/ADCMP573
connecting an external pull-down resistor from the HYS pin to GND, a variable amount of hysteresis can be applied. Leaving the HYS pin disconnected disables the feature, and hysteresis is then less than 1 mV as specified. The maximum hysteresis that can be applied using this method is approximately 25 mV. Figure 17 illustrates the amount of hysteresis applied as a function of external resistor value. The advantages of applying hysteresis in this manner are improved accuracy, stability, and reduced component count. An external bypass capacitor is not recommended on the HYS pin because it would likely degrade the jitter performance of the device.
60
50
HYSTERESIS (mV)
40
VOH
30
20
VOL
10
0
1
2
3 RHYS (k)
4
5
6
-VH 2
0
+VH 2
INPUT
04409-0-005
Figure 17. Hysteresis vs. RHYS Control Resistor Figure 16. Comparator Hysteresis Transfer Function
MINIMUM INPUT SLEW RATE REQUIREMENT
As with all high speed comparators, a minimum slew rate requirement must be met to ensure that the device does not oscillate as the input signal crosses the threshold. This oscillation is due in part to the high input bandwidth of the comparator and the feedback parasitics inherent in the package. Analog Devices recommends a minimum slew rate of 50 V/s to ensure a clean output transition from the ADCMP572/ ADCMP573 comparators unless hysteresis is programmed as discussed previously.
The customary technique for introducing hysteresis into a comparator uses positive feedback from the output back to the input. A limitation of this approach is that the amount of hysteresis varies with the output logic levels, resulting in hysteresis that is not symmetric about the threshold. The external feedback network can also introduce significant parasitics that reduce high speed performance, and can even induce oscillation in some cases. The ADCMP572/ADCMP573 comparators offer a programmable hysteresis feature that can significantly improve the accuracy and stability of the desired hysteresis. By
Rev. PrB | Page 11 of 16
04409-0-043
0
ADCMP572/ADCMP573 TYPICAL APPLICATION CIRCUITS
3.3V
Preliminary Technical Data
VCCI = 5.2V VCCO = 3.3V/5.2V 3.3V/5.2V 50 50 Q
VCCO
VCCI
VTP VIN VP VN VTN
50
50
Q
ADCMP572
Q
VIN VTH
ADCMP572
Q
04409-0-029
LATCH INPUTS
Figure 18. Zero-Crossing Detector with 3.3 V CML Outputs
Figure 21. Comparator with 0 V to 3 V Input Range and 3.3 V or 5.2 V Positive CML Outputs
VCCI = 5.2V
VCCI VCCO = 3.3V
50 50 Q
VTP VP VN VP VN VTN
VCCO
5V 75 100 100 50 50
ADCMP572
Q
ADCMP572
04409-0-030
04409-0-032
LATCH INPUTS
LATCH INPUTS
LATCH INPUTS
Figure 19. LVDS to50 Back-Terminated (RS)PECL Receiver
Figure 22. Interfacing 3.3 V CML to a 50 Ground Terminated Instrument
VCCI = 3.3V VCCO = 2.5V/3.3V 2.5V/3.3V 50 VIN VTH
+
VCCI VCCO = 3.3V VCCO 50
Q
50
50
ADCMP572
-
VP
Q
VN
ADCMP572
VCCO
04409-0-031
GND = -1V
Figure 20. Comparator with 1 V Input Range and 2.5 V or 3.3 V CML Outputs
Figure 23. Disabling the Latch Feature
VCCI VCCO VCCO 50 50
ADCMP572
HYS
Figure 24. Adding Hysteresis Using the HYS Control Pin
Rev. PrB | Page 12 of 16
04409-0-036
0 TO 5k
04409-0-035
LATCH INPUTS
750
04409-0-034
Preliminary Technical Data TIMING INFORMATION
Figure 25 illustrates the ADCMP572/ADCMP573 compare and latch timing relationships. Table 4 provides definitions of the terms shown in the figure.
ADCMP572/ADCMP573
LATCH ENABLE 50% LATCH ENABLE
tS tH
tPL
DIFFERENTIAL INPUT VOLTAGE
VIN VOD
VN VOS
tPDL
Q OUTPUT
tPLOH
50%
tPDH
tF
50%
Q OUTPUT
tR
Figure 25. System Timing Diagram
Table 4. Timing Descriptions
Symbol tPDH tPDL tPLOH tPLOL tH tPL tS tR tF VOD Timing Input to output high delay Input to output low delay Latch enable to output high delay Latch enable to output low delay Minimum hold time Minimum latch enable pulse width Minimum setup time Output rise time Output fall time Voltage overdrive Description Propagation delay measured from the time the input signal crosses the reference ( the input offset voltage) to the 50% point of an output low-to-high transition. Propagation delay measured from the time the input signal crosses the reference ( the input offset voltage) to the 50% point of an output high-to-low transition. Propagation delay measured from the 50% point of the latch enable signal low-to-high transition to the 50% point of an output low-to-high transition. Propagation delay measured from the 50% point of the latch enable signal low-to-high transition to the 50% point of an output high-to-low transition. Minimum time after the negative transition of the latch enable signal that the input signal must remain unchanged to be acquired and held at the outputs. Minimum time that the latch enable signal must be high to acquire an input signal change. Minimum time before the negative transition of the latch enable signal that an input signal change must be present to be acquired and held at the outputs. Amount of time required to transition from a low to a high output as measured at the 20% and 80% points. Amount of time required to transition from a high to a low output as measured at the 20% and 80% points. Difference between the input voltages VA and VB.
Rev. PrB | Page 13 of 16
04409-0-003
tPLOL
ADCMP572/ADCMP573 OUTLINE DIMENSIONS
3.00 BSC SQ 0.45 PIN 1 INDICATOR TOP VIEW 2.75 BSC SQ 0.50 BSC 12 MAX 1.00 0.85 0.80 SEATING PLANE 0.30 0.23 0.18 0.80 MAX 0.65 TYP 0.05 MAX 0.02 NOM 0.20 REF * COMPLIANT TO JEDEC STANDARDS MO-220-VEED-2 EXCEPT FOR EXPOSED PAD DIMENSION 1.50 REF
9 8
Preliminary Technical Data
0.50 0.40 0.30 PIN 1 INDICATOR
16 1
0.60 MAX
13 12
BOTTOM VIEW
1.65 1.50 SQ* 1.35
5
4
0.25 MIN
Figure 26. 16-Lead Lead Frame Chip Scale Package [LFCSP] (CP-16) Dimensions shown in millimeters
ORDERING GUIDE
Model ADCMP572BCP ADCMP573BCP Temperature Range -40C to 85C -40C to 85C Package Description LFCSP-16 LFCSP-16 Package Option CP-16 CP-16
Rev. PrB | Page 14 of 16
Preliminary Technical Data NOTES
ADCMP572/ADCMP573
Rev. PrB | Page 15 of 16
ADCMP572/ADCMP573 NOTES
Preliminary Technical Data
(c) 2004 Analog Devices, Inc. All rights reserved. Trademarks and registered trademarks are the property of their respective owners. PR04409-0-6/04(PrB)
Rev. PrB | Page 16 of 16

▲Up To Search▲

Price & Availability of ADCMP572

	To Download ADCMP572 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .